[Home ] [Archive]   [ فارسی ]  
:: Main :: About :: Current Issue :: Archive :: Search :: Submit :: Contact ::
Main Menu
Home::
Journal Information::
Articles archive::
For Authors::
For Reviewers::
Registration::
Contact us::
Site Facilities::
Ethics::
peer-review::
Indexing::
Article types::
::
Search in website

Advanced Search
..
Receive site information
Enter your Email in the following box to receive the site news and information.
..
Journal DOI

AWT IMAGE

..
Copyright Policy
This work is licensed under a Creative Commons Attribution-NonCommercial 3.0 
This Journal is licensed under a Creative Commons Attribution-NonCommercial 4.0
..
:: Volume 22, Issue 1 (3-2020) ::
J Babol Univ Med Sci. 2020; Volume 22 Back to browse issues page
Effect of Using Bulk fill Composites on Fracture Resistance of Maxillary Premolars with MOD Cavities
N Shadman , R Hoseinifar * , M Ghafar Poor , D Dortaj
2. Department of Operative Dentistry, School of Dentistry, Kerman University of Medical Sciences, Kerman, I.R.Iran , R_hoseiniffar@yahoo.com
Abstract:   (2577 Views)
BACKGROUND AND OBJECTIVE: Bulk fill composites are an innovative class of dental resin composite materials, developed to simplify the restoration procedures, and are preferred to conventional composites if they have good mechanical properties and marginal seal. The aim of this study was to evaluate the fracture resistance of premolar teeth with mesio-occlusodistal (MOD) cavities restored with bulk and conventional composites.
METHODS: In this experimental in-vitro study, 40 sound maxillary premolar teeth were randomly divided into five groups: Group I: Positive control, intact teeth. In the remaining four groups, MOD cavities were prepared. Group II: Negative control, unrestored teeth. In other groups, cavities were restored as follows; Group III: (X-tra fil, bulk filling with 4mm-thick increment), Group IV: (X-tra base, bulk filling+Grandio, incremental filling) Group V: (Grandio, incremental filling with 2mm-thick increment). The restored teeth were stored in distilled water for 24 hours at 37oC and thermocycled (500 cycles). Specimens were subjected to a compressive load until fracture, and the fracture resistance was recorded in Newton.
FINDINGS: The highest fracture resistance values were obtained in group I (1150±507 N) and the lowest in group II (85±62.51 N), which was significantly lower than other groups (p=0.001). The fracture resistance of bulk fill composites and conventional composite did not differ significantly with intact teeth.
CONCLUSION: The restoration of teeth with moderate MOD cavity size using bulk fill composites can restore the lost tooth strength to a level comparable to intact teeth and similar to conventional composite.
Keywords: Composite Resins, Tooth Fracture, Polymerization.
Full-Text [PDF 221 kb]   (1455 Downloads)    
Type of Study: Experimental | Subject: Restorative Dentistry
Received: 2019/10/31 | Accepted: 2020/01/25 | Published: 2020/10/31
Send email to the article author



XML   Persian Abstract   Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Shadman N, Hoseinifar R, Ghafar Poor M, Dortaj D. Effect of Using Bulk fill Composites on Fracture Resistance of Maxillary Premolars with MOD Cavities. J Babol Univ Med Sci 2020; 22 (1) :215-221
URL: http://jbums.org/article-1-9063-en.html


Rights and permissions
Creative Commons License This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Volume 22, Issue 1 (3-2020) Back to browse issues page
مجله علمی دانشگاه علوم پزشکی بابل Journal of Babol University of Medical Sciences

The Journal of Babol University of Medical Sciences is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Persian site map - English site map - Created in 0.05 seconds with 43 queries by YEKTAWEB 4660